MACHINE TAPS FOR CUTTING SCREWS
DOI:
https://doi.org/10.37406/2706-9052-2018-2-11Keywords:
screw cutting, threaded connection, taps, nutsAbstract
The common use of screw joints connections in engineering is caused by their simple construction, high load-bearing capacity, reliability and convenience of connection and disconnection of parts. The high use of screw joints is also explained by the fact that there are a lot of special screw parts adapted to a variety of structures, there is their broad standardization and low cost in terms of mass production. It is known that 60….70% of general machinery parts have screw joins. And the processing of these joints with cutting tools is a complex technological problem, especially in manufacturing the accurate screw holes. Research considers the efficiency performance of taps by means of reducing their breakdowns on the basis of the design of taps, taking into account the changes in their parameters in the process of screw cutting and the state of the individual parts of this tool. The progressive design machine taps for cutting screws are examined in the study. In this construction the deformation angle of the screw increases in terms of continuous teeth cutting teeth to 0.2 degrees and then stabilizes at the simultaneous operation of all the teeth on the winding of 0.175 degrees and gradually decreases when the fluctuations drop to zero when the cut screw teeth leave. On the basis of theoretical research it is recommended to improve the design of the device for cutting screws by curved taps. The advantage of the tap is the improvement of the work conditions: separation of chippings that helps to form a cleaner surface and it is very important when dealing with viscous materials. They also provide a greater density of taps regrinding to avoid joins of the holes and their break-downReferences
Arshinok, V.A., & Alekseev, G.A. (1976). Rezanie metallov i rezhushhij іnstrument [Metal cutting and cutting tools]. Moskow: Mashinostroenie. [in Russian]
Gevko, B.M. (2006). Tehnologija sel'skohozjajstvennogo mashinostroenija [The technology of agricultural engineering]. Kiev: Kondor. [in Russian]
Granovs'kij, G.I. (1954). Rezanie mettalov [Metal cutting]. Moskow: Mashgiz. [in Russian]
Zholobov, A.A., Kirillovich, V.A., & Mel'nichuk, P.P. (2008). Tehnologija avtomatizirovannogo proizvodstva [Automated production technology]. Zhitomir. [in Russian]
Kralin, A.K. (2009). Sovershenstvovanie tehnologicheskogo obespechenija plasticheskogo formoobrazovanija rіz'b na gajkah v uslovijah massovogo proizvodstva: dis. … kand tehn. nauk: 05.03.05 [Improving the technological support of plastic forming threads on the nuts in terms of mass production (Unpublished PhD dissertation)]. Donbasskaja gos. Mashinostroitel'naja akademija, Kramatorsk. [in Russian]
Ljubin, N.V. (1997). Issledovanie processa plasticheskogo formoobrazovanija vnutrennej metricheskoj rez'by instrumentov s radial'nym peremishheniem deformirujushhih plastin: dis. … kand tehn. nauk: 05.03.05 [Investigation of the process of plastic forming of an internal metric thread of tools with radial movement of deforming plates (Unpublished PhD dissertation)]. VGTU, Vinnica. [in Russian]
Matvienko, A.V. (1999). Povyshenie effektivnosti izgotovlenija tonkostennyh rez'bovyh izdelij: dis. … kand tehn. nauk: 05.02.08 [Improving the efficiency of manufacturing thin-walled threaded products (Unpublished PhD dissertation)]. Donbasskaja gos. Mashinostroitel'naja akademija, Makeevka. [in Russian]
Panov, A.A., Anikin, V.V., & Bojl, M.G. (1988). Obrabotka metal lov rezaniem: spravochnik tehnologa [Metal cutting: a technologist handbook]. Moskow: Mashinostroenie. [in Russian]
Petruha P.G. (Ed.) (1974). Rezanie konstrukcionnyh materialov, rezhushhie instrumeny i stanki [Cutting construction materials, cutting tools and machine tools]. Moskow : Mashinostroenie. [in 1. Arshinok, V.A., & Alekseev, G.A. (1976). Rezanie metallov i rezhushhij іnstrument [Metal cutting and cutting tools]. Moskow: Mashinostroenie. [in Russian]
Rodin P.R. (1990). Osnovy proektirovanie rezhushhih instrumentov [Basics of cutting tools designer]. Kiev: Vysshaja shkola. [in Russian]
Kosilova, A.G., & Meshherjakova, R.K. (Eds.) (1985). Spravochnik tehnologa-mashinostroitelja, tom 1 [Handbook of technologist-machine builder, vol. 1]. Moskow: Mashinostroenie. [in Russian]
Kosilova, A.G., & Meshherjakova, R.K. (Eds.) (1985). Spravochnik tehnologa-mashinostroitelja, tom 2 [Handbook of technologist-machine builder, vol. 2]. Moskow: Mashinostroenie. [in Russian]
Filonenko, S.N. (2008). Rezanie metallov [Metal cutting]. Kiev : Tehnika [in Russian]
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2019 Podilian Bulletin: Agriculture, Engineering, Economics
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
Authors contributing to Public Policy and Administration agree to publish their articles under a Creative Commons Attribution-NonCommercial 4.0 International (CC BY-NC 4.0) License, allowing third parties to share their work (copy, distribute, transmit) and to adapt it, under the condition that the authors are given credit, and that in the event of reuse or distribution, the terms of this licence are made clear.
